VersaTube VS3406014420WS Instrukcja Obsługi

Przeglądaj online lub pobierz Instrukcja Obsługi dla Otwieracz drzwi garażowych VersaTube VS3406014420WS. VersaTube VS3406014420WS Instructions / Assembly Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 46
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
UNIVERSAL ASSEMBLY INSTRUCTIONS
FOR VERSATUBE BUILDINGS
CONTRACTOR SERIES
2” X 4” FRAMES
PAGE 1
Our unique assembly process quickly transforms the individual pieces into a finished
structure that will give you years of service. Great care has been taken to ensure
complete satisfaction with your purchase. In the unlikely event that there are any missing
or damaged parts or if you simply need technical assistance, please call our Toll Free Hot-
line at 1-800-900-7222 and your questions will be addressed promptly. Thank you for
choosing the Versatube Building System.
© MSMP INC. 2/12/11
ZINST-CS
Przeglądanie stron 0
1 2 3 4 5 6 ... 45 46

Podsumowanie treści

Strona 1 - 2” X 4” FRAMES

UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE BUILDINGS CONTRACTOR SERIES 2” X 4” FRAMES PAGE 1 Our unique assembly process quickly transforms the in

Strona 2

STEP 3: ASSEMBLING THE TRUSS Note: The two end trusses will have no collar tie or bracing. The basic interior truss has a collar tie and the W web A

Strona 3 - ATTENTION:

#12 SELF-DRILLING SCREW WEB BRACE AND BRACE BRACKET The illustration below is a web brace to brace bracket joint. This illustration shows two braces

Strona 4

STEP 4: INSTALLING THE END WALL TRUSS You will need a crane or boom attachment to a skid loader to lift and install the trusses to the side posts. Y

Strona 5 - FOUNDATION NOTES

The illustration below is a typical end wall installation for 40’ wide buildings. Please see your drawings to determine the parts and layout of the en

Strona 6 - ANCHORING THE BASE RAILS:

The illustration below shows a typical assembly of an end wall vertical. USE 2 SCREWS IN EACH VERTICAL JOINT PP-60 PIN PLATE HEIGHT EXTENSION FOR BUIL

Strona 7

STEP 5: INSTALLING INTERIOR TRUSS SECTIONS Using the crane or boom attachment lift a full truss assembly (truss with web braces) and insert the eave

Strona 8

#12 SELF-DRILLING SCREW PAGE 16 CLAMP MOTOR CYCLE STRAP STRING SIDE POST STEP 6: CHECKING THE EAVES FOR HEIGHT AND PLUMBING THE SIDE POSTS When all

Strona 9

STEP 7: INSTALLING ROOF PURLIN HAT CHANNEL AND REMAINING SIDE GIRT HAT CHANNEL Install the first run of roof purlin hat channel at the eave corner.

Strona 10 - STEP 3: ASSEMBLING THE TRUSS

INSTALLING THE REMAINING SIDE HAT CHANNEL GIRTS See your drawing package side elevation to see the layout a side girts on your building. You should h

Strona 11 - TYPICAL TRUSS

INSTALLING A WALK DOOR FRAME IN SIDE OF BUILDING WITH BASE PLATES A walk door frame is typically a door header tube 2” x 4” cut to fit the space betw

Strona 12

PAGE 2 SAFETY AND HAZARD INSTRUCTIONS IMPORTANT Read the following safety warnings and all instructions in their entirety prior to installation. If yo

Strona 13 - 4’ TYPICAL, 8 PLA

INSTALLING A WALK DOOR FRAME IN SIDE OF BUILDING WITH BASE RAILS We recommend that you cut out the base rail where walk doors will be located. Cut ou

Strona 14

INSTALLING A WALK DOOR FRAME IN SIDE OF BUILDING WITH BASE RAILS CONTINUED INSTALLING NAILER TUBES AROUND DOOR FRAME: In your kit you will find (1) n

Strona 15 - TRUSS WITH SHORT EAVE

42” 36”, 48” OR YOUR ROUGH OPENING HEIGHT BK-10 ANGLE BRACKETS 6 PLACES VERTICAL FRAME TUBE 2 X 4 X WINDOW ROUGH OPENING HORIZONTAL FRAME TUBE 2” X 4

Strona 16 - #12 SELF-DRILLING SCREW

TOP NAILER TUBE BOTTOM NAILER TUBE TOP WINDOW FRAME TUBE VERTICAL NAILER TUBE SIDE WINDOW FRAME TUBE #13 X 2” PAN HEAD, SELF-DRILLING SCREW BOTTO

Strona 17

INSTALLING THE WALK DOOR Pre-hung walk doors are typically attached to the frame with screws through the door jamb into the building frame on both si

Strona 18

INSTALLING A VERSATUBE WALK DOOR INTO A 2” X 4” BUILDING FRAME from the inside. These instructions apply only to the VersaTube flange mounted walk

Strona 19

INSTALLING TRIM AROUND THE VERSATUBE DOOR INSTALLED FROM THE INSIDE OF THE BUILDING There are two types of trim used to trim around the walk door. J-T

Strona 20

SIDE POST DOOR FRAME DOOR OPENS IN THRESHOLD SHEETING LEDGE HAT CHANNEL J TRIM VERTICAL SHEET METAL ANGLE TRIM 3 7/8” X 2 1/4” PAN SCREW #12 x 1” SEL

Strona 21

INSTALLATION OF SIDE WALK DOOR TRIM (J-TRIM) If door J-Trim is not built in to your door install it at this time. Cut two pieces of Side J-Trim to fi

Strona 22

INSTALLING WINDOW The windows available from VersaTube are sliders, vertical or horizontal. The windows are aluminum and are flange mounted. The win

Strona 23 - SELF-DRILLING SCREW

ATTENTION: IT IS IMPORTANT THAT YOU READ THE FOLLOWING NOTE BEFORE STARTING THE ASSEMBLY OF YOUR BUILDING NOTE: If during the installation process you

Strona 24 - INSTALLING THE WALK DOOR

PAGE 30 INSTALLING J-TRIM AROUND WINDOW Cut a piece of Bottom J-Trim 2” longer than the window width. Center it along the bottom of the window and fa

Strona 25 - VIEW FROM INSIDE BUILDING

INSTALLING TRIM AROUND END GARAGE DOORS To trim the garage doors you will use two types of trim. (Angle trim and J-trim) The angle trim will finish o

Strona 26 - BUILDING

STEP 8: INSTALLING SHEET METAL PANELS AND TRIM NOTE: If you will be adding insulation to the building, you must install the insulation as you install

Strona 27 - TRIM (ANGLE AND J-TRIM)

STEP 2: NOTE: If you will be adding insulation to the building, you must install the insulation as you install the sheet metal. The insulation will b

Strona 28 - FRONT FLANGE

STEP 2: INSTALLING ADDITIONAL SIDE PANELS If you are installing Insulation you will now cut a piece of 6’ wide insulation 5” longer than the eave heig

Strona 29 - INSTALLING WINDOW

STEP 3: INSTALLING SHEET METAL PANELS ON THE ENDS OF THE BUILDING IMPORTANT NOTE: These installation instructions are for 5 rib panels with ribs on 9

Strona 30 - WINDOW TRIM

INSTALLING INSULATION ON THE END WALLS OF THE BUILDING:  Place your double sided tape on the lower flush mounted girt and on the frame at the top a

Strona 31

PAGE 37 STEP 4: INSTALLING CORNER TRIM Cut corner trim to fit the corner height of your building. If the building has a eave height over 10’ you will

Strona 32

PAGE 38 STEP 6: INSTALLING ROOF SHEET METAL PANELS LENGTH OF ROOF PANELS: 12’ wide 6’-5”, 14’ wide 7’-6”, 16’ wide 8’-6”, 18’ wide 9’-6”, 20’ wide 1

Strona 33 - STEP 2:

STEP 7: INSTALLING GABLE TRIM Gable trim will be Denver Style trim about 5 1/2” deep and 10’ to 10’-2” long. Most buildings will require a piece of t

Strona 34

BASIC PARTS LIST: SIZES AND QUANTITIES WILL VARY BY BUILDING WIDTH AND LENGTH SEE THE PACKING SLIP WITH YOU BUILDING FOR PART NUMBERS AND QUANTITIES.

Strona 35 - FIRST PANEL

STEP 8: INSTALLATION OF RIDGE CAP RIDGE CAP WILL COME IN 10’-6” LENGTHS. YOU WILL OVERLAP PIECES 6” UNTIL YOU GET TO THE OTHER END OF THE BUILDING

Strona 36

INSTALLING YOUR GARAGE DOOR IN A VERSATUBE FRAME Note that the Versatube frame is all steel with no overhead ceiling joist. You must deviate from the

Strona 37 - EAVE TRIM

Step 4 Installing Additional Door Sections Follow the door manufacturer’s instructions and assemble door section 2. Note that each door section uses a

Strona 38

ATTACHMENT OF DOOR TRACK WITH & WITHOUT EXTENSION ANGLE TO RAFTER IN BUILDING WITHOUT A LOW HEADROOM KIT INSTALLED. Before you start, make sure t

Strona 39

INSTALLING THE TOP DOOR SECTION With the door tracks installed it is now time to install the last or top door section. Place the last door section on

Strona 41

WHEN ATTACHING A WALK/ACCESS DOOR, GARAGE DOORS OR WINDOWS TO A VERSATUBE STEEL FRAME YOU WILL NEED TO FOLLOW THE

Strona 42

FOUNDATION NOTES  You should check with your local building official or Code Enforcement Office for the foundation requirements in your County. Y

Strona 43

PAGE 6 STEP 1 IF YOU ARE USING BASE RAILS: BASE RAIL ASSEMBLY If you are using the base plates proceed to the next page Place the starter base rails i

Strona 44 - SIDE VIEW

STEP 1 IF YOU ARE USING BASE PLATES: SIDE POST LAYOUT STEP 1: MARKING THE SIDE POST LOCATIONS Using a pencil or other marking devise, on the top of t

Strona 45 - PAGE 45

STEP 2: POSITIONING AND ANCHORING THE SIDE POST/ HEIGHT EXTENSIONS ON THE SLAB The outside of each post should be set 1 1/2” from the edge of the she

Strona 46

INSTALLING A SIDE GARAGE DOOR FRAME The following assembly instructions are for a typical side door 10’ wide x 2’ shorter than the eave height. Side d

Komentarze do niniejszej Instrukcji

Brak uwag